Sea Gull Lighting Fan Sea Gull Lighting Ceiling Fan User Manual

0

Out of 0 Ratings

Owner's of the Sea Gull Lighting Fan Sea Gull Lighting Ceiling Fan gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 6
 
Copyright 1998, Sea Gull Lighting Products, Inc.
TROUBLESHOOTING GUIDE
SUGGESTED REMEDY
TROUBLE
1. If fan does not start:
2. If fan sounds noisy:
3. If fan wobbles:
Touching
Ceiling
Figure 1
Blade Tip Down:
Blade Tip Up:
Fan Blade
Fan Blade
Figure 2
Blade Brackets
4. If light does not work:
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or
wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please
check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installa-
tion, please call our Customer Service Center at the number printed on your parts list insert sheet.
Warning: Before servicing or cleaning unit, switch power off at service panel and lock service disconnecting means
to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked,
securely fasten a prominent warning device, such as a tag, to the service panel.
1. Check main and branch circuit fuses or circuit breakers.
2. Check line wire connections to fan and switch wire connections in switch housing.
CAUTION: Make sure main power is turned off.
3. Make sure forward/reverse switch is firmly in up or down position. Fan will not operate when switch is in the
middle.
4. Make sure that shipping stabilizer tabs have been removed from motor (see installation step #13).
1. Check to make sure all screws in motor housing are snug (not over tightened).
2. Check to make sure the screws which attach the fan blade holder to the motor are tight.
3. Check to make sure wire nut connectors in switch housing are not rattling against each other or against the
interior wall of the switch housing.
CAUTION: Make sure main power is turned off before entering switch housing.
4. If using an optional Ceiling Fan Light Kit, check to be sure the screws securing the glassware are finger tight.
Check to be sure light bulb is tight in socket and not touching glass shade(s). If vibration persists from
glass, remove glass and install a 1/4" wide rubber band on glass neck to act as an insulator. Replace glass
and tighten screws against rubber band.
5. Some fan motors are sensitive to signals from Solid State variable speed controls. DO NOT USE a Solid
State variable speed control.
6. Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after this period.
1. Make sure that the ridge of the canopy engages the notch in the downrod ball. (See illustration in Step #6
of Downrod Mount installation).
2. Check that all blades are screwed firmly into blade holders.
3. Check that all blade holders are tightened securely to motor.
4. Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and junction box
is mounted firmly to ceiling joist.
5. Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on
the ceiling above the tip of one of the blades. Measure this distance as shown in Figure 1. Keeping measure
within 1/8", rotate the fan until the next blade is positioned for measurement. Repeat for each blade. If all
blade levels are not equal, you can adjust blade levels by the following procedure. To adjust a blade tip
down, insert a washer (not supplied) between the blade and blade holder at the screw closest to the motor
(Figure 2). To adjust a blade tip up, insert washer (not supplied) between the blade and blade holder at the
two screws farthest from the motor (Figure 2).
6. If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the
weight and possibly result in smoother operation.
1. Check blue wire from fan to make sure it is connected to hot wire from house.
2. Check for loose or disconnected wires in fan switch housing.
3. Check for loose or disconnected wires in light kit.
4. Check for faulty light bulbs.
CAUTION: Make sure main power is turned off before entering switch housing.
FOR TECHNICAL SUPPORT CALL:
(866) 449-2821

   Find Your Products By Category